Search:
Products meeting the search criteria
Sort By:
This website uses cookies. By continuing you permit us to deploy cookies, as detailed in our Privacy Policy.
Accept
The Shopping Cart is empty
These are "display wheels" as supplied with some of our 7mm kits. The wheels are a press fit on a steel axle.
The wheels are intended for use with a static model.
There are four wheels and two axles in a packet. The wheels are based on Mansell pattern wheels which can be difficult to source.
This pattern wheel was commonly used on passenger stock.
..
£6.00
These are "display wheels" as supplied with some of our 7mm kits. The wheels are a press fit on a steel axle.
The wheels are intended for use with a static model.
There are four wheels and two axles in a packet. The wheels are based on 8 spoked wheels which were often used on goods vehicles and early coaches.
..
£6.00
This kit makes one carriage bogie. The bogie matches our products and methods of construction. it is recommended that the minimum radius curve is around 2 feet (600 mm approximately). The models are based on a style of construction that was used on many railways.
The kit consists of 3d printed parts (random colour). The 3D printed parts are made from PLA (Carbon Fibre) which is resilient.
The bogie is readily assembled.
The wheelbase of the bogie is a scale eight feet.
This kit can a..
£5.00
About this Vehicle:
The GNR had several types of brake van. The brake van type that this model is the 8 wheeled version with vertical planking. This vehicle was initially used for mineral traffic. Sixty vehicles were introduced in 1913-1914.
These vehicles were long lived there were still 46 in service in 1948 from a declared 60 in service in 1922 (from the inventory at grouping), until the early 1960's.
One of these vehicles has been preserved.
This Kit features:
Pre-cut MDF..
£34.20 (Promotion)
About this Vehicle:
The GNR had several types of brake van. The brake van type that this model represents is the twenty ton, 6 wheeled version with horizontal planking. This vehicle was mainly used for heavy goods and mineral traffic.
These brake vans have been described in books (e.g. 19th Century Railway Drawings by A. Prior, and LNER Wagons by P. Tatlow) and the Model Railway press (Especially an article in "Model Railway News" December 1967). A representative model will enhan..
£17.10 (Promotion)
About this Vehicle:
The GNR had several types of brake van. The brake van type that this model is the 8 wheeled version with vertical planking. This vehicle was initially used for mineral traffic. Sixty vehicles were introduced in 1913-1914.
These vehicles were long lived there were still 46 in service in 1948 from a declared 60 in service in 1922 (from the inventory at grouping), until the early 1960's.
One of these vehicles has been preserved.
This Kit features:
Pre-cut woo..
£20.90 (Promotion)
About this Vehicle:
This kit represents a Great Northern Railway (GNR) Diagram 281 (D281) Third Class Brake.
This Great Northern Railway (GNR) Diagram 281 (D281) Third Class Brake was a ubiquitous vehicle produced by the GNR. Approximately 370 examples of this type were included in the stock inventories at the beginning of the 20th century. Similar vehicles were used by the East Coast Joint Stock (ECJS) and joint lines. One of These coaches has been preserved.
This Kit features:
Laser c..
£21.85 (Promotion)
About this Vehicle:
This kit represents a Great Northern Railway (GNR) Diagram 156 (D156) composite.
This vehicle is a good example of a six wheeled composite produced in quantity by the GNR. Approximately 120 of this type were included in the stock inventories at the beginning of the 20th century.
This Kit features:
Laser cut MDF carcass
Overlaid card Panels
Printed in pre-grouping livery
3D printed roof (and Guards Lookouts if appropriate)
Our underframe kit ..
£21.85 (Promotion)
About this Vehicle:
This model represents a Great Northern Railway (GNR) Diagram 243(D243) Six compartment Third Class coach (Also known as an excursion third).
This vehicle was produced by the GNR in 1901. Approximately 34 of this type of vehicle were included in the stock inventories at the beginning of the 20th century. One of these coaches has been preserved.
This Kit features:
Laser cut MDF carcass
Overlaid card Panels
Printed in pre-grouping livery
3D printed roof (and Guards Look..
£21.85 (Promotion)
About this Vehicle:
This model represents the standard, outside framed, covered van used by the GNR. In 1906,the GNR recorded 1563 covered vans. At grouping, 669 covered vans are recorded as surviving into LNER stock. These covered vans were actively constructed from about 1867 (Stirling) until about 1905 (Gresley) when outside framed vehicles were gradually replaced by inside framed stock. Photographic records of wagon stock (RAIL 326/682 and RAIL 326/1072 at the National Archives, UK) depict a number o..
£32.30 (Promotion)
There were over 280 vans of this type in service with the GNR until grouping in 1922. These vans were fully fited with vaccum brakes. They were used for express goods traffic. This model construction is similar to GN04-W004 GNR covered Van.
This Kit features:
Pre-cut wood sides and ends.
Sturdy construction
3D printed axleguards and brake components
3D printed roof and buffers
Our wheels D3D-00 (2 axles wheels + mansell inserts) are compatible with this kit
Build impressive ..
£15.20 (Promotion)
About this Vehicle:
This kit represents a Great Northern Railway (GNR) Diagram 303 (D303) Full Brake van.
This brake van and its variants was a common sight on the Great Northern Railway and later on the L&NER for many years. Approximately 80 vehicles of this type were owned by the GNR at the beginning of the 20th Century.
This Kit features:
Laser cut MDF carcass
Overlaid card Panels
Printed in pre-grouping livery
3D printed roof (and Guards Lookouts if appropriate)
Our ..
£21.85 (Promotion)
This 7mm scale ("O" gauge) kit is primarily made from laser cut and etched MDF with 3D printed roof and underframe components. This kit can be completed to represent any one of several versions of a standard type used by the Great Northern Railway.
About this Vehicle:
The GNR had several types of brake van. The brake van type that this model is the 4 wheeled version with horizontal planking. It was made in 10 ton, 15 ton and 20 ton versions. The physical dimensions overall were the sam..
£32.30 (Promotion)
This 7mm scale ("O" gauge) kit is primarily made from laser cut and etched MDF with 3D printed roof and underframe components.
This Kit features:
Pre-cut MDF sides and ends.
Sturdy construction
3D Printed roof
3D printed underframe incorporating axleguards.
Brake components
About this Vehicle:
The GNR had several types of brake van. The brake van type that this model represents is the twenty ton, 6 wheeled version with horizontal planking. This vehicle was mainly use..
£32.30 (Promotion)
About this Vehicle:
The brake van type that this model is based on, with horizontal planking, a light 10 ton Van.. This was the most numerous type of brake van. It had brakes on one side only, actuated within the cabin. Over 200 examples survived into the LNER and beyond.
These brake vans have been described in books (e.g. 19th Century Railway Drawings by A. Prior, and LNER Wagons by P. Tatlow) and the Model Railway press (Especially an article in "Model Railway News" December 19..
£15.20 (Promotion)
About this Vehicle:
The GNR had several types of brake van. The brake van type that this model is based on, with vertical planking, was a 20 ton version that replaced earlier vans from the early 1900's onwards. It was given diagram 1602/N. The physical dimensions overall were the same as the earlier vans. A few vans were vacuum fitted in later years. There were two significant variations of this van. Initially, the van was constructed with stanchions at each end, similar to existing vans constructed ..
£15.20 (Promotion)
This 7mm scale ("O" gauge) kit is primarily made from laser cut and etched MDF with 3D printed roof and underframe components. This kit can be completed to represent any one of several versions of a standard type used by the Great Northern Railway.
About this Vehicle:
The GNR had several types of brake van. The brake van type that this model is based on, with vertical planking, was a 20 ton version that replaced earlier vans from the early 1900's onwards. It was given diagram 1602/..
£32.30 (Promotion)
About this Vehicle:
This model represents the standard, outside framed, covered van used by the GNR. In 1906,the GNR recorded 1563 covered vans. At grouping, 669 covered vans are recorded as surviving into LNER stock. These covered vans were actively constructed from about 1867 (Stirling) until about 1905 (Gresley) when outside framed vehicles were gradually replaced by inside framed stock. Photographic records of wagon stock (RAIL 326/682 and RAIL 326/1072 at the National Archives, UK) depict a number o..
£15.20 (Promotion)
The Great Northern Railway (GNR) built a small number of butter lard and milk vans. Similar vehicles were used for the conveyance of Fruit, meat and fish products. There were detail differences between the vehicles however they were all based on the standard 16ft body and incorporated a clerestory roof which makes them attractive and unusual vehicles.
A few vehicles survived into LNER ownership in 1922.
This Kit features:
Pre-cut wood sides and ends.
Sturdy construction
3D printed axleguards..
£15.20 (Promotion)
About this Vehicle:
This kit is based on the original GWR siphon version O1. This was a four wheeled vehicle and should not be confused with the later six wheeled siphon which took the same designation after this van became extinct.
The original vehicle was produced in several lots between 1871 and the late 1880's. There were two distinct variations with differing door profiles. Sufficient parts are provided to complete either one of the versions of the vehicles. The kit consists..
£21.85 (Promotion) Last one
About this Vehicle:
This 7mm ("O" Gauge) kit represents a Great Western Railway four wheeled milk van (O1)
This was a four wheeled vehicle and should not be confused with the six wheeled siphon which is also available as a kit from Diagram3D.
The original vehicle was produced in several lots between 1871 and the late 1880's. There were two distinct variations with differing door profiles. Sufficient parts are provided to complete either one of the versions of the vehicles. The kit is..
£36.10 (Promotion)
About this Vehicle:
This 7mm ("O" Gauge) kit represents a Great Western Railway six wheeled milk van (O2)
This was a six wheeled vehicle. It was developed for the transportation of milk in churns. It was also used for transporting fish.
Thys kit is made from MDF with detail components etched into card overlays and 3D printed components including a roof, axleboxes and brake components.
These vehicles were modified over their lifetimes in keeping with applicable regulations. In general ..
£45.60 (Promotion) Last one
About this Vehicle:
This 7mm ("O" Gauge) kit represents a Great Western Railway six wheeled milk van (O3)
This was a six wheeled vehicle. It was developed for the transportation of milk in churns. It was also used for transporting fish.
Thys kit is made from MDF with detail components etched into card overlays and 3D printed components including a roof, axleboxes and brake components.
These vehicles were modified over their lifetimes in keeping with applicable regulations. In general ..
£45.60 (Promotion)
About this Vehicle:
This 7mm ("O" Gauge) kit represents a Great Western Railway six wheeled milk van (O4)
This was a six wheeled vehicle. It was developed for the transportation of milk in churns. It was also used for transporting fish. It was a popular design.
Thys kit is made from MDF with detail components etched into card overlays and 3D printed components including a roof, axleboxes and brake components.
These vehicles were modified over their lifetimes in keeping with appl..
£45.60 (Promotion)
Out of Stock
Details
These miniature stepper motors can be used to switch point motors or other accesories on model railways.
There are a number of advantages when using stepper motors:
Unlike servo motors, the points will not lose position if the power is lost. Once the point has changed the power can be switched off, unlike a servo which needs a continual power supply in order to maintain its position. These stepper motors are robust.
Finally, these mini stepper motors are easily linked to low cost microprocessors su..
£5.00
NER First (Diagram 68): This carriage was one of a series of 32ft six wheeled carriages which were designed and built by the North Eastern Railway in the latter part of the 19th Century. They used a standard underframe and replaced earlier vehicles. This model represents a first class carriage (diagram 68). The NER inventory contained over fifty similar vehicles in the 1890's.
This kit features:
Laser cut MDF carcass
Overlaid card Panels
3D printed roof
Our underframe kit D3D-05..
£21.85 (Promotion) Last one
NER Third (Diagram 15): This type of carriage was the most numerous vehicle produced by the North Eastern Railway (NER). Approximately 1000 examples of this type of carriage were produced from the mid 1880’s until 1895. A drawing of this vehicle exists at the National Railway Museum (LNER drawing 1829D, formerly NER drawing 68a). This drawing was referred to during the design of this model.
This kit features:
Laser cut MDF carcass
Overlaid card Panels
3D printed roof
Our under..
£21.85 (Promotion)
NER Van (Diagram 21):
This model represents a North Eastern Railway Guards van (diagram 21). This model represents a Guards van, diagram 21. The NER inventory contained about two hundred similar vehicles in the 1890's. They were originally designed for passenger traffic, some were used for milk traffic and others passed into goods service
This kit features:
Laser cut MDF carcass
Overlaid card Panels
3D printed roof and Guards Lookouts
Our underframe kit D3D-05-CF iscompatible..
£21.85 (Promotion)
This carriage was one of a series of 32ft six wheeled carriages which were designed and built by the North Eastern Railway in the latter part of the 19th Century. They used a standard underframe and replaced earlier vehicles. This model represents a composite carriage with a central luggage compartment, diagram 9. The NER inventory contained over 200 similar vehicles in the 1890's.
This kit features:
Laser cut MDF carcass
Overlaid card Panels
3D printed roof
Our underframe kit D3..
£21.85 (Promotion) Last one
NER Luggage Third (Diagram 13): These carriages were very similar to Diagram 15 thirds, see our produuct NE04-D015. One passenger compartment was replaced by a luggage compartment. A drawing of this vehicle exists at the National Railway Museum (LNER drawing 1830D, formerly NER drawing 71a). This drawing was referred to during the design of this model. Originally, the livery would have been standard NER maroon with yellow lining. Roofs were white when new.
This kit features:
Laser cut MDF carcass
..
£21.85 (Promotion)
NER Van Third (Diagram 20):
This model represents a Guards can with two third class compartments (diagram 20). The NER inventory contained about a hundred similar vehicles in the 1890's.This carriage was one of a series of 32ft six wheeled carriages which were designed and built by the North Eastern Railway in the latter part of the 19th Century. They used a standard underframe and replaced earlier vehicles.
This kit features:
Laser cut MDF carcass
Overlaid card Panels
3D printed roof ..
£21.85 (Promotion)
These "OO" disc wheels are approximately a scale 3ft 5in in diameter, excluding the flanges.
The wheels are metal (with an insulated axle).
The wheels are suitable for use with our coach kits.
The 3D printed inserts give an effective representation of a Mansell pattern wooden centred wheel.
Two axles and four 3D printed Mansell pattern inserts are included.
This is sufficient for one four wheeled vehicle.
..
£6.00
These "OO" disc wheels are approximately a scale 3ft 5in in diameter, excluding the flanges.
The wheels are metal (with an insulated axle).
The wheels are suitable for use with our coach kits.
The 3D printed inserts give an effective representation of a Mansell pattern wooden centred wheel.
Three axles and six 3D printed Mansell pattern inserts are included.
This is sufficient for one six wheeled vehicle.
..
£9.00
These "OO" disc wheels are approximately a scale 3ft 5in in diameter, excluding the flanges.
The wheels are metal (with an insulated axle).
The wheels are suitable for use with our coach kits.
The 3D printed inserts give an effective representation of a Mansell pattern wooden centred wheel.
Four axles and eight 3D printed Mansell pattern inserts are included.
This is sufficient for one bogie vehicle or two four wheeled vehicles,
..
£12.00
This kit makes a set of axleguards which suit all our six wheeled 4mm coach products. The axleguards permit our models to negotiate sharp curves without extensive modifications to the kits. Although the images show a vehicle negotiating a Hornby type 2 radius curve (approximatley 1.5 feet or approximatley 438 mm), it is recommended that the minimum radius curve is around 2 feet (600 mm approximately)
The kit consists of 3d printed parts (random colour). The parts are made from PLA-CF which is stron..
£7.00
-80x80.jpg "GNR Outside Framed Van")
A step by step walk through of the assembly of this 4mm scale model of a GNR outside framed covered goods van with examples of the many uses of this vehicle.
..
About this Vehicle:
** G3 (13.5mm scale) vehicle **
L&NWR 2nd Class Brake Van, 1850's.
This kit represents a historical London and North Western Railway Railway (LNWR) carriage of the mid 1800's, designed and produced in-house by Diagram3D.
This kit is created with 3D printer and laser technology. It is pre-coloured. The kit is designed to be easy to complete.
This Kit features:
3D printed sides, ends and underframes in colour.
3D printed roof and oil lamps
3D prin..
£102.60 (Promotion)
About this Vehicle:
This kit represents a historical London and North Western Railway Railway (LNWR) 21ft Full Brake of the mid 1800's, designed and produced in-house by Diagram3D.
This kit is created with 3D printer and laser technology. It is pre-coloured. The kit is designed to be easy to complete.
The kit is based on historical drawings.
This Kit features:
3D printed sides, ends and underframes in colour.
3D printed roof and oil lamps
3D printed solebars
Sturdy construction
..
£45.60 (Promotion)
About this Vehicle:
This model of an LNWR 3 compartment 1st class vehicle is typical of the short vehicles of the early period. This model relies on drawings and similar vehicles of the period.
This kit is created with 3D printer and laser technology. The kit is designed to be easy to complete.
This Kit features:
3D printed parts in colour
3D printed sides, ends and underframes
3D printed roof and oil lamps
3D printed solebars
Sturdy construction
Includes wheels for static model
..
£45.60 (Promotion)
About this Vehicle:
** G3 (13.5mm scale) vehicle **
L&NWR 2nd Class coach, 1850's.
This kit represents a historical London and North Western Railway Railway (LNWR) carriage of the mid 1800's, designed and produced in-house by Diagram3D.
This kit is created with 3D printer and laser technology. It is pre-coloured. The kit is designed to be easy to complete.
This Kit features:
3D printed sides, ends and underframes in colour.
3D printed roof and oil lamps
3D printed ..
£102.60 (Promotion)
About this Vehicle:
This kit represents a historical London and North Western Railway Railway (LNWR) four compartment second class carriage of the mid 1800's, designed and produced in-house by Diagram3D.
This kit is created with 3D printer and laser technology. It is pre-coloured. The kit is designed to be easy to complete.
The kit is based on historical drawings.
This Kit features:
3D printed sides, ends and underframes in colour.
3D printed roof and oil lamps
3D printed solebars
..
£45.60 (Promotion)
About this Vehicle:
This kit represents a historical London and North Western Railway Railway (LNWR) carriage of the mid 1800's, designed and produced in-house by Diagram3D.
This kit is created with 3D printer and laser technology. It is pre-coloured. The kit is designed to be easy to complete.
The kit is based on information gathered about a grounded coach body by the LNWR society.
This Kit features:
3D printed sides, ends and underframes in colour.
3D printed roof and oil lamps
3..
£45.60 (Promotion)
About this Vehicle:
This is a lasercut kit of a historical London and North Western Railway Railway (LNWR) carriage of the mid 1800's, designed and produced in-house by Diagram3D.
The kit is based on information gathered about a grounded coach body by the LNWR society. This kit is also available in 7mm scale.
This Kit features:
Laser cut MDF carcass
Card panels for sides and ends.
3D printed roof and oil lamps
3D printed solebars
Our wheels D3D-00 (2 axles wheels + mansell inserts..
£21.85 (Promotion)
About this Vehicle:
** G3 (13.5mm scale) vehicle **
L&NWR 3rd Class coach, 1850's.
This kit represents a historical London and North Western Railway Railway (LNWR) carriage of the mid 1800's, designed and produced in-house by Diagram3D.
This kit is created with 3D printer and laser technology. It is pre-coloured. The kit is designed to be easy to complete.
The kit is based on information gathered about a grounded coach body by the LNWR society.
This Kit features:
3D..
£102.60 (Promotion)
About this Vehicle:
The London & North Western Railway (LNWR) had several versions of Covered Carriage Trucks (CCT). According to an early LNWR diagram book there were about 140 CCT’s, of various lengths, in service around the end of the 19th century. These vehicles had many modifications over their lifetime. Many other pre-grouping railways had similar vehicles.
This particular type of CCT had a wheelbase of ten feet and was 19 feet in length. The livery illustrated is an approximatio..
£38.00 (Promotion)
*** Clearance item superceded by current LNW706 ***
This is a lasercut kit of a historical railway vehicle of the 19th Century, designed and produced in-house by Design3D. It represents a LNWR Covered Carriage truck (CCT), a type of vehicle that was commonly found in passenger trains during the pre-grouping period. The kit is designed for 7mm scale, "O" gauge.
The LNWR had several versions of Covered Carriage Trucks (CCT). This model was created using information from diagram books, works dr..
£17.10 (Promotion)
About this Vehicle:
This is a lasercut kit of a historical London and North Western Railway Railway (LNWR) carriage of the mid 1800's, designed and produced in-house by Diagram3D.
The vehicle on which this model is based was a 21ft four wheeled brake van. The model includes
Laser cut MDF carcass
Card panels for sides and ends.
3D printed roof and oil lamps
3D printed solebars
3D printed guards lookouts
Our wheels D3D-00 (2 axles wheels + mansell inserts) are compatible wi..
£23.75 (Promotion)
About this Vehicle:
This kit represents a historical London & North Western Railway Railway Horsebox (13ft. 6in.) of the mid 1800's, designed and produced in-house by Diagram3D.
This kit is created with 3D printer and laser technology. It is pre-coloured. The kit is designed to be easy to complete.
The kit is based on information from a grounded body which was researched by the London & North Western Railway Society.
This Kit features:
3D printed sides, ends and underframes in ..
£38.00 (Promotion)
This is a laser cut kit of a historical railway vehicle of the 19th Century. This kit represents an open carriage truck, a type of vehicle that was commonly found in passenger trains during this period. The kit is designed for 7mm scale, "O" gauge. It is designed and produced in-house by Diagram3D.
This kit is manufactured in MDF and card with some 3D printed parts. It is supplied with printed instructions.
Additional images can be found at Gallery LNW705
This kit is created with 3D print..
£23.28 (Promotion)
About this Vehicle:
This kit represents a historical London and North Western Railway Railway (LNWR) second class brake carriage of the mid 1800's, designed and produced in-house by Diagram3D.
This kit is created with 3D printer and laser technology. It is pre-coloured. The kit is designed to be easy to complete.
The kit is based on historical drawings.
This Kit features:
3D printed sides, ends and underframes in colour.
3D printed roof and oil lamps
3D printed solebars
Sturdy co..
£45.60 (Promotion)
About this Vehicle:
** G3 (13.5mm scale) vehicle **
L&NWR 2nd Class Brake Van, 1850's.
This kit represents a historical London and North Western Railway Railway (LNWR) carriage of the mid 1800's, designed and produced in-house by Diagram3D.
This kit is created with 3D printer and laser technology. It is pre-coloured. The kit is designed to be easy to complete.
This Kit features:
3D printed sides, ends and underframes in colour.
3D printed roof and oil lamps
3D prin..
£102.60 (Promotion)
About this Vehicle:
** G3 (13.5mm scale) vehicle **
L&NWR 2nd Class coach, 1850's.
This kit represents a historical London and North Western Railway Railway (LNWR) carriage of the mid 1800's, designed and produced in-house by Diagram3D.
This kit is created with 3D printer and laser technology. It is pre-coloured. The kit is designed to be easy to complete.
This Kit features:
3D printed sides, ends and underframes in colour.
3D printed roof and oil lamps
3D printed ..
£102.60 (Promotion)
About this Vehicle:
This kit represents a historical London and North Western Railway Railway (LNWR) second class saloon carriage of the mid 1800's, designed and produced in-house by Diagram3D.
This kit is created with 3D printer and laser technology. It is pre-coloured. The kit is designed to be easy to complete.
The kit is based on historical drawings.
This Kit features:
3D printed sides, ends and underframes in colour.
3D printed roof and oil lamps
3D printed solebars
Sturdy c..
£45.60 (Promotion)
About this Vehicle:
This is a lasercut kit of a historical London and North Western Railway Railway (LNWR) carriage of the mid 1800's, designed and produced in-house by Diagram3D.
This model of an early LNWR tri-composite carriage is based on a vehicle which was acquired by the Mawddwy Railway from the LNWR. The vehicle was photographed around 1900 when passenger services were withdrawn. The photographic evidence gives an excellent idea of the construction of this vehicle.
Laser cut MDF carc..
£21.85 (Promotion)
About this Vehicle:
This model of an early LNWR tri-composite carriage is based on a vehicle which was acquired by the Mawddwy Railway from the LNWR. The vehuicle was photographed around 1900 when passenger services were withdrawn. The photographic evidence gives an excellent idea of the construction of this vehicle.
This kit is created with 3D printer and laser technology.The kit is designed to be easy to complete.
This Kit features:
3D printed sides, ends and underframes.
3D printed roof ..
£45.60 (Promotion)
Information
Customer Service
 |